HORN - ZNAČKY :: Q ACOUSTICS :: CONCEPT

HOME
- AKTUALITY
- *** DEALS ***
- PRODUKTY
- ZNAČKY
- OUTLET
- PODPORA
- SERVIS
- KARIÉRA
- KONTAKT
ZNAČKY
- ALPINE
- ARGON
- AUDIOLAB
- BANG & OLUFSEN
- BLAUPUNKT
- BOWERS & WILKINS
- CAVUS
- CHORD COMPANY
- CLASSÉ
- COMFORT MAT
- DALI
- DENON
- ELIPSON
- FOCAL
- FOCAL CAR
- GINEOS
- GLADEN
- GOLDRING
- IN-AKUSTIK
- JL AUDIO
- JL AUDIO CAR
- LEAK
- MARANTZ
- MILTY
- MOSCONI
- NAIM
- NORSTONE
- OPERA LOUDSPEAKERS
- POLK AUDIO
- Q ACOUSTICS
- QED
- QUAD
- SAPHE
- SONOPOWER
- SONOS
- SONOVISION
- SONUS FABER
- SUMIKO
- THINKWARE
- UNISON RESEARCH
- WET SOUNDS
- WHARFEDALE
- WILSON
Q ACOUSTICS
- Q ACTIVE
- CONCEPT
- 5000 SERIES
- 3000c SERIES
- Q SUB
- Q INSTALL
CONCEPT
CONCEPT 500

Designed to appeal to discerning audiophiles, the Concept 500 achieves a perfect balance between art and science. It is a loudspeaker that is at once, stylish, contemporary, fine-sounding and astonishingly accurate. It couples low directivity with wide bandwidth, good sensitivity and sensible impedance. This makes the new Concept 500 both room-friendly and an easy load to drive, allowing amplifiers to deliver their best performance
To create a stereo soundstage which gives as good an impression of width, depth and height as that found in a live performance requires high quality drive units, a well designed crossover and an accurately constructed cabinet. To achieve this, Q Acoustics formed a truly talented team with many years of experience in the design, engineering and manufacture of world-class loudspeakers. A combination that resulted in a state-of-the-art loudspeaker worthy of any high-end system
Great care has been taken in both the design of the crossover and the selection of high grade components, to introduce virtually zero noise and distortion. The 4th-order Linkwitz-Riley topology which gives an excellent response both on and off-axis
A method, known as P2P™ (Point to Point) bracing, supports the parts of the cabinet that need to be stiffened to deal with low frequency panel vibrations
Constructed in three separate layers and filled under pressure with a non-setting gel, this damps the cabinet walls and converts higher frequency vibrations into heat
Mechanically decoupled mounting which effectively isolates the HF driver and speaker cabinet from reciprocal vibrations that would otherwise be transmitted between them
The Mid/Bass voice coil has an uncommonly large diameter of 35mm which allows increased ‘shove’ and higher power handling - as well as reducing compression
Tall loudspeakers tend to suffer from resonances caused by unwanted pressure gradients. Specially designed Helmholtz Pressure Equalisers (HPE™) balance out these pressure irregularities
The rear access panel has been constructed to maintain the integrity of the Dual Gelcore™ cabinet. The Concept 500 is equipped for bi-wiring or bi-amping with terminals which can accept bare wires, spades or 4 mm banana plugs
The cast aluminium base of the Concept 500 is designed without large flat areas or additional adornments to discourage unwanted acoustic reflections. The resulting elegant design is underpinned with a choice of carefully engineered feet to immovably couple the loudspeaker to any surface
Frequency Response: 41 Hz – 30 kHz
Nominal Impedance: 6 Ω
Minimum Impedance: 3.7 Ω
Recommended Power: 25 - 200 W
Distortion (120 Hz – 20 kHz): 0.2 %
Crossover Frequency: 2.5 kHz
Mid Bass / Driver: 2 x 165 mm
High Frequency Unit: 28 mm
Size (W x H x D): 400 x 1150 x 350 mm
Weight: 42 kg